How To Change Pull Cord 6hp Briggs And Stratton Lawnmower

With the weather cleared up, you finally head out to your backyard to requite it a nice cutting. You lot have an older Briggs and Stratton push mower that has served you well for all these years. But as you pull the lawnmower'south pull string to start it, it ends up in your hand, and the other end goes spinning into the starter assembly. This happens much more often with older lawnmowers and probably means that the pull string needs to exist replaced. Luckily for you, fixing the issue is not a challenging job. Depending on your experience, it volition only take one-half an hr, and your lawnmower shall be up and running again.

How to supersede the pull cord on a Briggs and Stratton lawnmower, step-past-step:

Step 1: Get the right replacement pull string
Step two: Unscrew the starter associates
Step 3: Remove the old pull cord
Footstep four: Supersede the erstwhile pull string with a new one
Pace v: Reassemble the lawnmower parts

There are a few necessary steps on how to prepare the pull cord. However, these steps may vary from i model to model. The standard action for all the models is to reach the pulley located within the starter assembly. The pull cord may suspension down when it gets old or gets stuck somewhere inside the pulley.

This weblog post provides you with the nitty-gritty details that i needs to be enlightened of for performing the pull cord replacement.

Contents

1 Step by footstep, How to Supplant a Briggs and Stratton Lawnmower Pull Cord:
- ane.one ● Stride 1: Get the needed tools and textile
  - 1.1.1 – Required tools:
  - ane.1.two – Required Cloth:
- 1.2 ● Step 2: Unscrew the starter associates
  - i.2.one – Step 2.ane. Pull string location:
  - 1.ii.2 – Step ii.2. Remove the plastic cover:
  - 1.2.3 – Step 2.3. Detach the gas tank:
  - i.two.four – Step 2.4. Remove the engine shroud:
- 1.3 ● Step 3: Remove the onetime pull string:
  - 1.3.1 – Step 3.1. Cutting the knot on the rope:
  - 1.three.2 – Stride three.2. Pull out the former pull cord:
  - one.3.iii – Step iii.3. Rewind the pulley bound:
  - one.3.4 – Step three.iv. Rotate the pulley in an anticlockwise direction:
  - one.iii.five – Step 3.5. Lock the pulley:
- 1.4 ● Step 4. Replace the old pull string with a new one:
  - 1.4.1 Length of pull string:
  - one.iv.2 – Step 4.one. Attach the rope to the pull handle:
  - ane.4.iii – Footstep 4.2. Attach the new pull cord to the starter housing:
2 ● Step 5: Reassemble the lawnmower parts:
- - 2.0.1 – Footstep v.i. Reinstall the engine shroud:
  - 2.0.2 – Step v.two. Place the gas tank back:
  - 2.0.3 – Stride 5.three. Adhere the engine's plastic cover:
3 Related Questions:
- 3.ane ane. How long should a lawnmower cord be?
- iii.2 two. What is the office of a pull cord?
- three.3 3. How to reduce the pull cord length?
- 3.4 four. Why is my pull cord stuck?
  - 3.4.1 – ane. Quondam grass or debris stuck upwardly inside the pulley:
  - 3.four.2 – 2. Broken recoil spring:
  - iii.4.iii – three. Damaged pull cord:
4 Final Remarks:

Pace past stride, How to Supersede a Briggs and Stratton Lawnmower Pull Cord:

The method beneath explains all the required steps to prepare a lawnmower'south pull cord to get the lawnmower up and running once more

● Step 1: Go the needed tools and material

Before we tin can replace the pull cord, y'all demand to make sure that you have the required tools and textile. The about important is the replacement cord. Make sure that information technology fits your model lawnmower.

– Required tools:

You should have the post-obit tools to help you in the procedure:

Screwdriver
Nut driver
Pliers

– Required Material:

Only a couple of materials are required to complete the job, which is every bit follows:

New rope
Friction match stick

● Step 2: Unscrew the starter associates

– Pace 2.one. Pull string location:

The pull cord is tied to the starter disc of the lawnmower. So first, we need to locate the starter disc on the lawnmower.

– Step 2.2. Remove the plastic cover:

A lawnmower usually has a plastic comprehend that covers its engine. Remove the screws holding this plastic cover and pull this plastic embrace out.

– Step 2.3. Detach the gas tank:

Subsequently successfully removing the plastic cover, the next stride is to pull the gas tank out. Remove the 4 screws property the gas tank from the top and the fifth spiral located at the lesser of the gas tank. Just loosen the screw at the bottom a little and rotate the gas tank outwards instead of eradicating it.

– Footstep 2.4. Remove the engine shroud:

The final step is to remove the entire engine shroud. Unscrew the bolts holding the engine shroud and lift it off. At present yous shall run across the whole starter disc, to which the pull cord is attached.

● Stride 3: Remove the erstwhile pull cord:

– Step 3.1. Cut the knot on the rope:

Plow over the starter assembly, and you would see the old pull cord. With the help of pliers, cutting the knot on the rope.

– Step iii.2. Pull out the old pull cord:

Now, pull out the onetime pull cord but be conscientious because it creates tension on the starter pulley, and you don't want to break the starter spring.

– Footstep 3.three. Rewind the pulley spring:

Once the one-time pull cord is removed, rewind the pulley spring in an anticlockwise management and verify that the starter spring is not cleaved. If the spring is cleaved, bank check out our commodity on "How to prepare pull string spring."

– Footstep iii.iv. Rotate the pulley in an anticlockwise management:

After you lot have completed checking the spring, rotate the pulley in an anticlockwise direction, and requite it virtually five rounds. This should exist done so that the hole on the caster and the starter housing hole are aligned.

– Step 3.5. Lock the pulley:

The final step is to lock the pulley in this position by placing a screwdriver inside the starter housing. This shall also continue you condom from unnecessary injuries as the caster is property a big amount of tension at the moment.

● Stride iv. Replace the former pull cord with a new one:

Length of pull string:

Most of the lawnmowers use a size v or a size six pull cord. Simply it is recommended to measure the length of your old pull string and purchase the new one of the same size and length as recommended by Briggs and Stratton for your item model number.

– Step iv.one. Adhere the rope to the pull handle:

One time you have bought the new pull string, you demand to thread the rope through the pull handle.

Burn the end of the rope: Fire one of the rope'southward ends with a match stick's help and give it a lilliputian twist. This prevents the rope from fraying.
Tie a knot: Now, pass this end of the rope through the pull handle and necktie a knot, which shall prevent the rope from coming out of it.

– Step 4.ii. Attach the new pull cord to the starter housing:

Burn the stop of the rope: Accept the other end of the rope and burn down it with the help of a match stick. Delight give information technology a little twist so that it forms a pointed end.
Attach the rope to the starter housing: Laissez passer this pointed stop through the starter housing hole. Tie a knot at this stop of the rope to forestall it from coming out of the starter housing.
Wind the pull cord: Next, remove the screwdriver and permit the caster current of air the rope back completely.

● Step five: Reassemble the lawnmower parts:

Nosotros know that you must be a trivial wearied after this hectic task. But don't worry, the primary piece of work is done, and all you demand to do now is reassemble the lawnmower parts.

– Step 5.one. Reinstall the engine shroud:

Reinstall the engine shroud by tightening the bolts that hold the shroud in place.

– Footstep 5.2. Place the gas tank back:

Push dorsum the gas tank in, tighten the screws at the peak and the i at the bottom of the gas tank with a screwdriver'southward help.

– Step 5.iii. Attach the engine'due south plastic encompass:

The final step is to install the plastic cover back into its place by tightening its bolts.

1. How long should a lawnmower cord exist?

The length of the lawnmower string depends upon the model of the lawnmower. The main thing regarding the pull cord's size is that it should non be likewise thick, as a thick pull cord would not rewind around the caster.

Commonly v, five.5, or six size pull cords are used.

2. What is the function of a pull string?

The pull cord is like a key, equally it helps to start the lawnmower. The pull string is wrapped around a caster within the lawnmower'southward engine in the off state. As y'all push the pull cord, it rotates the caster, and it moves a piston. A spark is produced as a result, which starts the lawnmower.

iii. How to reduce the pull cord length?

Sometimes, a pull string of the desired length is not available in the market. And so you need to cut it according to the desired size. For that, you first need to place a marker on this rope according to the required length and and then cut it using a scissors. Then, using a lucifer stick, burn the finish of the rope cutting recently and twist it. This is done to prevent the rope from fraying.

4. Why is my pull cord stuck?

Many reasons may cause the pull string to become stuck. A few of them are:

Old grass or droppings may be stuck up inside the starter pulley
Broken recoil spring
Damaged pull cord

– 1. Old grass or debris stuck up inside the pulley:

Sometimes there is a build-upward of mud and grass within the starter pulley. To remove this clay and grass, you need to open up the lawnmower's starter housing past following the steps above and then remove the debris using a screwdriver.

– 2. Broken recoil spring:

This is a scarce scenario, simply the recoil jump inside the starter housing may be broken in some cases. You need to bank check the starter housing, in this case, to rule out the trouble.

– iii. Damaged pull cord:

A lawnmower that has been put into use for a very long time by and large gets its pull cord damaged. To fix this problem, you should accomplish the above commodity.

A lawnmower'southward pull cord is i of the essential parts of a lawnmower. It'southward similar a fundamental to a car, and without it, it's impossible to start the lawnmower and trim your garden'south grass. To fix the pull cord, one has to reach the starter housing located inside the lawnmower'southward engine. The above article is a step-by-step guide to set the pull string. Y'all should likewise wear safe glasses and gloves during the procedure mentioned in a higher place to protect yourself from unnecessary injuries. As well, don't forget to perform timely maintenance of other lawnmower parts to prolong its life.

Source: https://www.gardentoolexpert.com/how-to-replace-the-pull-cord-on-a-briggs-and-stratton-lawnmower-step-by-step/

Posted by: litchfordsagems66.blogspot.com